Aston Martin DB9, V8V, DBS coolant expansion tank     NEW
£480
4G43-19B518-BD reinvented in alloy! In stock   

END OF TEST

DB7 Vantage Front Wheel Bearings  NEW
Prices for exchange basis tba
Front wheel bearings going on a DB7 Vantage? Pressing out the old and in new is not for the faint hearted! Exchange uprights with new bearings ready fitted takes a lot of bench work out of the job. This is R/H but L/H available too. Depends on how much can be swapped over . Or can give a price with all new ancillaries so the whole area should not need to be touched again for another 20 years!

6019 Cobra Security Emulator for early i6 pre-airbag   NEW.
£300 or £700 with modern fobs
Emulator/defeater for immobiliser part of system, £300 bottom line ….. and the door locks will still work of the existing fobs!
OR the above plus modern Cobra fobs ( so 6019 components fully removed) £700 bottom line. Pics of fobs to follow

Pre-airbag DB7 exhaust r/h over axle and rear expansion box.
£185
Not new, but high grade stainless steel construction supplied by AML recently to replace pipes that failed at the joint between the 2 pipes, but not needed. In perfect condition and will last longer than the originals!

Starter Motor for DB7 Vantage, Vanquish, and DB9
£166 service exchange or £210 outright
Not new units, [09.85122 / 09-85122] but guaranteed good. In stock

Air Condition Compressor for all I6 DB7s
£498 exchange, or outright £618
As new A/C compressor [89.83266 / 89-83266] built for us by professionals, just using some parts off the originals, such as the rear manifold plate.

DB7 Front Fog/Indicator Light Seals
£30 per pair
Whether you like them or not, these are the seals that can fit around the front fog/ indicator lamps on DB7 Vantage and Vanquish.
Not available from Aston Martin.

DB7 Power Steering leaks?
Seal ring £5, Cap £22, tank  £192
On all 6 cylinder DB7s and the 500 plus DB7 Vantages, these parts are relevant! All these individual parts are new and available. AML only sell the whole thing. So buy here the part(s) depending on the need.

DB7 Vantage Mesh Grill
£172
Brand new with fitting kit. For sale on behalf of a customer who decided not to fit.

DB7 Inlet Air Duct Pipe.
£26
Pre-airbag pipe/elbows were made of cloth and all have fallen apart by now,  that means the puddle height is reduced to the bottom of the hole into the airbox. The new pipe/elbow raises that height to the original ~ 15cms, reducing risk of water ingestion.

Vantage Larini sports catalytic converter/cats.
£1000  – BOTH NOW SOLD
Fitted March 2018, taken off March 2024. All good, but the new owner wanted the car back to a quieter exhaust sound. The Larini ones sit better distance from the auto box! Selling on behalf of the owner £1000 for the pair

Front Under Tray for all i6 DB7s
£384
Newly made Front Under Tray for all i6 DB7  [ PartNo: 78.84119 / 78-84119 ]. Textured finish, better than originals (which are no longer available anyway). Drilled ready for fitment.

DB7 Drinks Bottle / Cup Holder
£20
The Internet is awash with owners asking “Why does my Aston not have a cup holder?”  Well you can have one now – designed for the DB7.
No holes need drilling or altering the car in any form.

DB7 HANDBRAKE CABLE
£132
Front cable cheaper and sturdier than AML’s, complete with sleeve  and grommet! [AML 30.83218 / 30-83218, Jaguar MHF5150BA] 
I also have stock of the two rear handbrake cables [30.84493 / 30-84493].

DB7 Rear Outer Hand-brake Cable
£115
Includes the heat sleeving (which is not included in OEM’s cable), Left and right cables are the same [30.84493 / 30-84493]. Half AML’s price, and every bit as sturdy. 

DB7 Window Control ECU
£432
New, complete kit with instructions. Can be used on Mk1, Mk2, & Mk3 window instalations [AML 37.81867 / 37-81867, 37.111361AA / 37-111361AA, 76.111926AA / 76-111926AA] irrespective of whether the ECU or the motor sensing has a fault. Works slightly differently but even faster!  Made from bare PCBs in the UK. . 
Good second-hand Mk2 and Mk3 ECUs are also often available.

DB7 WINDOW REGULATORS
–
Brand new, not refurbished, will fit directly to pre-airbag car RHS, so no need to update the ECU.
But all gone & no longer available!

DB7 Vantage Brake Light Switch
£96
Exchange service, Rebuilt with new heavy duty micro switches [37.85792 / 37-85792].   
No longer available from AML.

DB7 i6 Power Steering Pump
£415
Fully rebuilt assembly, available on service exchange basis.  A surcharge of £120 to be added & refunded when servicable old unit is returned. .
This pump is not available from AML as a complete assembly.  It is made of parts 24.81731, 24.81027 and 24.81731 / 24-81731, 24-81027, 24-81731,  thus providing a pre-assembled ‘bolt-on’ part.

DB7 Header/Expansion Tank for I6
£380
Made with love in alloy, complete with  sensor grommet (only) 

Throttle Cable RHD DB7  i6
£114
All metal construction, no plastic.  [AML original part No 14.90182 / 4-90182]  Remade as no longer available 

DB7 Etched “Aston Martin” Rear Chrome Panel
Made in Holland, the chrome panel on the boot/trunk lid, above the rear number plate, is etched with “Aston Martin” – and looks like it should have been there from the beginning. Obtainable new or exchange basis for all variants of DB7 (except USA spec.)

DB7 Front Disc Brake Upgrade Kit  (i6)
£2670 inc VAT
Disc diameter increased to 315 mm, far larger swept area acting further out from centre. New Disc bells and alloy calipers, thus massive weight saving over originals. 6 pot calipers available in black, silver or green. Stainless steel braided flexi lines included in the kit. Better braking, better heat control, less weight.

DB7 Instrument cluster dimmer switch
with knob £25, without knob £20.
New, easy to desolder wires from old dimmer and resolder to new, with original plug. No longer available from AML or Jaguar [p/n 37.84389 / 37-84389, LJA6500AB]

DB7 Evaporator temp sensor/probe
£168 new
Specially made in the UK. Sturdier than the originals, fits positively right into the evaporator to read temperature sensitively and stops compressor from running-on too long and freezing evaporator into a big lump of ice!  Might seem expensive but a third of AML price and no longer available from Jaguar [89.83652 / 89-83652, JLM748]. Individually hand built

DB7 BONNET SWITCH BOOT/GAITOR
£6   [ ALL SOLD ]
This fits all airbag DB7s (i.e. 6 cyl and Vantage), plus Vanquish too. Normally the switch itself continues to work, but the rubber boot disintegrates and looks horrid. Not an easy fit, but DIY possible.

DB7 VANTAGE COOLANT EXPANSION TANK
£380
This is a new, custom made, all alloy tank, [AML part 32.86358 / 32-86358] complete with new level probe and conventional type filler/pressure cap. We made several and all have increased clearance in the area of the left hand throttle butterfly. Very nicely put together yet cheaper than from AML.

DB7 HEADLAMP REAR ACCESS PANELS
£42
Remanufactured as no longer available from AML, these will fit either side and come complete with clips and foam, ready to install. [Original p/n 88.83632rh / 88-83632rh, 88.83633lh / 88-83633lh or last p/n 88.86528 / 88-86528]  

DB7 CLUTCH KIT
£1584
Clutch kit for Aston Martin DB7 i6. Complete kit, new flywheel, pressure plate, driven plate, release bearing and specially made carrier, plus bolts.

DB7 SEAT MECHANISM SIDE COVERS
£30  each

Seat mechanism side covers, left and right hand. [P/N 74.83169 / 74-83169 and 74.83168 / 74-83168]. Fits all pre air bag DB7s AND air bag DB7s upto MY97.5. No longer available from Aston Martin or Jaguar. Have been remanufactured.

DB7 NEW BOOT/TRUNK FLOOR
£396 each
New remanufactured – strong, lightweight, professionally trimmed, really good fit (better than the originals)  [AML part number 83.82611 / 83-82611], to fit all DB7s except early Vantages as they had a skinney, inflated spare wheel, which stopped the boot being flat!

DB7 REPEATER TELL-TALES – INDICATOR/HAZARD WARNING
Can’t see/hear your turn-indicators flashing – a common problem. Here’s an easy fix: a replacement relay with an additional interior tell-tale light/led, plus a louder ‘buzzer’.  The tell-tale led can be positioned at the top or bottom of the instrument binnacle (whichever is in your sight-line).  Similarly the buzzer can be positioned closer to the driver on a volante (to overcome wind noise).
Fitted, or a DIY job with full instructions.
Available for pre-airbag i6 and later models.
i6: £96 on relay exchange basis, later models:£80.

DB7 PIVOT CLIP FOR KNEE BOLSTER
£14 each
These are re-manufactured and clip the leather bolster (the one by the driver’s knees) to the metal struts.

DB7 KEYS
£48 each   [ ALL SOLD ]
Genuine original ‘programmable’ key blanks for DB7, not required for pre-air bag but essential on all after that!  None left now, all the Blacks and the Reds have been sold, and I don’t think any more of either will be available.

DB7 V12 STARTER BUTTONS
£105 repair only
Later type 091855 – No stock unfortunately, but we can repair yours with a quick turn-around.

DB7 BRAKE MASTER CYLINDER – PRE -AIR BAG
p.o.a.
In stock [AML 33.81741 / 33-81741], rebuilt units, including ABS actuation parts, but not the fluid reservoir on top. Service exchange only. I don’t think you will find these anywhere else……..”

DB7 i6 SUPERCHARGERS
£3150 Exchange
Rebuilt units with new bearings and re Teflon coated rotors in stock, but exchange only [32.84452 / 32-84452, 08.80823 / 08-80823] suitable for pre or airbag i6 DB7s..

DB7 PRE AIR-BAG EXHAUST PIPES AND SILENCERS
£660 plus carriage.
Pre air bag overaxle pipes and rear silencers/mufflers, to original pattern in high quality Stainless Steel and will fit the original tail trims if still serviceable, otherwise new chrome tips can be provided at £70 each.

DB7 PRE AIR-BAG ‘STRAIGHT THROUGH’ EXHAUST PIPES
£490 plus carriage.
Pre air bag over-axle pipes with straight through rear pipes, just a VERY slight increase in sound level but NOT loud! Same applies with tail trims as with the mufflers above.

DB7 BOOT/TRUNK GAS STRUTS
£41 each
Does your boot lid only just stay open?… or not?

DB7 VANTAGE REAR BUMPER SUPPORTS
£39 each

Custom made from stainless steel, will not rust away like originals. Available left and right hand.

DB7 VANTAGE STAINLESS STEEL GOODRIDGE BRAKE HOSES
Brake hoses for DB7 Vantage

Front pair – £83
Rear pair  – £72
.

DB7 DOOR MIRROR POST-SLEEVE/TRIM
£22

Available for all 6 cylinder DB7s. Shiny black finish so does not go white with car polish. Very good fit, far more robust than the originals.

DB7 & VOLANTE (I6 & VANTAGE TONNEAU SIDE BLADES
£20 each.

As per pic, the originals break with age! The back two are different and seem to be fit for purpose, so have had the side blades made of a tougher plastic yet certainly no thicker than the originals.
New are black and need to be riveted in place of originals by a good DIYer, or a trim shop.

DB7 (ALL) FRONT SUSPENSION BUMP STOP SPACERS  (except GTs which are thinner).
£33 (ABS) or £70 (Alloy) each

New alloy ones now available here at £70 (or from AML at £151!).  The black ABS replacements (£33) shown are as tough and light as the originals and will not corrode.  Because the original alloy spacers are in a water and steel environment they are crumbling fast!  

DB7 (ALL) FRONT SUSPENSION BUMP STOP
£48 each
The Bump Stops itself [ 23.83416 / 23-83416  ] bolts THROUGH the spacer. Given the corrosion mentioned above, if the spacer has not fallen apart, there will definitely be little chance of the old bump stop bolts being able to be removed from the old spacer.

DB7 INTERCOOLER RADIATORS
£540

Intercooler radiator for 6cyl DB7s. [ 32.81569 / 32-81569 or 32.84128 / 32-84128]

DB7 INTERCOOLER CHARGE AIR COOLER REBUILDS AVAILABLE
£1500 exchanged for your old unit

These units are not available from AML and indeed the division of IMI Marston who originally built the intercoolers no longer exists, but we have access to their jig. The one shown is a good unit from an airbag i6 and is available for sale on an exchange basis for £800. Exchanged units will then have the internal radiator replaced with a new matrix and will be available for £1500 plus deposit of £800 till the old unit returned.

DB7 VANTAGE ANTI-TRAMP FRAME
Price £985 – less than 1/2 of AML’s mild steel price!

Have been out of stock for some time [ 26.122053AD / 26-122053AD ], so have now moved to re-fabrication of them in Stainless Steel… no need to paint, powder coat or underseal! These are a work of art, shame they are underneath the car!

DB7 FRONT NUMBER PLATE PLINTH AND SEAL STRIP
£86 

Fits ALL DB7s. Better made, of heavier gauge ABS, yet cheaper than AML [ 78.82545 / 78-82545 ].

DB7 A/C COMPRESSOR OUTPUT PIPE & HIGH PRESSURE PORT
Price £155   OUT OF STOCK until Dec.

These are now no longer available from Jaguar [ their p/n was MHE7340BA ] and are £620+ from AML [ 89.82073 / 89-82073 ], so have been specially re-fabricated to original spec. The pipe connects to the back of the compressor and goes up, past the alternator, to the input side of the condensor, on ALL 6 cylinder DB7s.

DB7 HUB CAP LOCKING BOLTS FOR i6 (set of 4)
Price £85

Original locking bolts used a whole set of combinations of 3 pin layout, so giving a fair degree of individuality/security. Current AML stock has 3 pins equidistant, so one key fits all! Another disadvantage is that, being steel, all (past and present) rust, so look unsightly and seize in alloy wheels. The Stainless Steel ones offered here will, keep their finish, not accumulate road dirt and not seize in the threading into the roadwheel.

DB7 REAR LIGHTS SURROUND
£25

This is an ABS extrusion of the surround for the R/H rear light for ALL DB7s with standard rear lights. The customer would have to cut off excess for their particular car as there are variations through the years! L/H available too. These are far sturdier than the originals.

DB7 I6 AUTO GEARBOXES
£985
Not new, but should be fine – sumps are cleaned out and new filter fitted.